Let's See Now, Where Were We?

Last time I posted about the patio palapa, the project had barely gotten started and that post was on 24 September 2018.

I suppose it would be better to give a brief synopsis of the project from the beginning.

Getting thatch from the bush, where you have to get it, has become expensive. The plants are still further into the bush and are becoming scarce, so it was time to rethink roofing materials.

We were very happy with the way the parking palapa turned out, so we thought, continue with a good idea for this.

What It Looked Like To Start

It was really looking raggedy and neglected. We waiting about as long as we could. Any more, and the lumber used for the structure would begin to rot before our eyes, and we'd be looking at completely starting over. So this was the perfect time.

Mario's crew, the same guys who redid our pool and its enclosure, were just finishing up a house for Sonja and Dan, friends of ours, building over in Ranchito near the airstrip.

We like their work, and attention to detail, so hiring them was really an easy decision.

Lots of Air Vents

I think in places, there was more air and daylight than thatch. It gave us a good indicator that it was time, time, time to get something done.

They got started removing the thatch and broken wood. That took pretty much all of the first day.

Once all the thatch was gone and the patio swept, it almost looked presentable again.

Framing Started

With things cleaned up, it looks nice.

You can see that the framing for the soffit area (I guess) and the framing for the screens which will go floor to ceiling is underway.

We have a ceiling fan that only works slowly. I suspect its capacitor is failing. It was in the utility room off the kitchen and has spent the past few months in a box.

Dianna suggested we replace the lantern chandelier with the fan and light because there are times when we used to use the palapa, where there was no breeze. It becomes stifling, and a fan might just do the trick to make it a nice, relaxing reading and relaxing nook.

Tool Repair

As with most tools down here, things break. One of their cordless drills, with a keyless chuck, naturally broke. Not good timing. Almost everything with this project involves screws, so it was really needed.

Forty-five minutes work, and it was back functioning again. I don't know if they were able to repair the chuck or if it required a replacement from Lano's Hardware.

Adding More Varnish

The next step after getting all the lumber in place was to apply a liberal dose of varnish.

Of course, when they started that, they were only able to do a partial coat when it started to rain. The rain continued off and on for three days.

Even after it stopped, it still took most of a day to dry the lumber out enough to be able to apply more varnish.

Screen Framing Done Too

Getting some real progress now. It's looking almost like it's time for the zinc roof to be installed.

But wait, there's more. I'm sure the framing for the screens will need a coat or two of the varnish.

I Think There's More To Do

Refilling a painting cup must mean that more varnish has to be applied.

That's what they're doing this afternoon. It was really doubtful that they'd be able to work this afternoon.

The forecast was calling for more rain and thunderstorms all afternoon.

Parking Palapa Gets a New Top

The thatch on the parking palapa came to its end a few days ago. We had the roof restored with 'zinc' as they call it, sheet metal by any other name would smell as sweet, or something like that.

Just Getting Started

Even though the thatch was beginning to show its age, developing more holes everytime we had a heavy rain, taking it down was still not an easy task. The way the thatch is wrapped around the horizontal stick part of the frame meant that each frond had to be pulled apart individually.

It Doesn't Go As Fast As You Think

Now we're beginning to see the skeleton. Quite an impressive structure. We'll be keeping that underneath the zinc.

Starting Framing For Screws

And, just like that, the thatch is all gone. Now they're putting up board framing so there is something to screw the zinc into, and to even up the roof framing so that it looks smooth and the zinc panels don't look wavy from the ground.

First Piece of Zinc Going Up

I just made it out of the house in time to catch the first panel of zinc going up. Already looks impressive, eh?

Close to Being Done

Here it is, almost all done, complete with ridge caps, which are shaped strips of zinc designed to fit over the ridges and help provide a water-resistant roof.

Underside View

This is what it looks like from underneath. Really shows off the original structure. I like the way it looks.

Tricky Corner

This corner of the palapa always was tricky. We had to cut back the thatch here because the corner of the concrete house was a bit close. Endher trimmed back the zinc roofing to allow for that as well, in order to keep rain from running down the house wall. He said a bit of the gutter will be run around there to help with drainage.

Endher Fitting Gutter Sections

 Yesterday was a full day for the crew. Fitting gutter sections, digging trenches and putting it all together. It sure looks good as the end result.

Chillin'

Sidewalk superintendent taking in the view of the workplace.

Digging Trench for Floor Drain

Here's the trench for the floor drain going in. This will make number four for the floor drains along the driveway. Combined with the flow from the gate area French drain, the Mennonite house, parking palapa, the floor drains, and the new house gutters, there's a large volume of water shooting out of the pipe into the canal during and shortly after a rainfall.

3" Drain Everything Connects To

Here's the three-inch drainpipe that runs pretty much the length of the property (it's roughly 250 or so feet long.

One Side Done

The gutter (eves-troughs to those of you used to calling them that) is in place on the north side. Soon to become blue like the rest. The structure is really looking nice.

Fitting Clamps for Downspout

Endher fastening the downspouts to the brackets. I really like the metal brackets they use. I hadn't seen them before Endher and the boys used them. It keeps the pipe off the wall surface and facilitates painting too.

Positioning Floor Drain

The four-inch floor drain going in. A two-inch drain would work, except the metal top is exceedingly thin and wrinkles up at the drop of a hat. the metal on the 4" drain is about 1/4" thick so it's extremely durable.

View From Mennonite House

A much cleaner view now from the upper landing of the Mennonite house.

Making It All Pretty

Touching up the final coat of blue on the gutters.

View As You Approach

This view is as you approach the palapa on the driveway. Looks very nice. All that's left now, is for the crew to install a shelter for my bike so that I can come and go easily and the bike is somewhat protected from the elements.